 |
 |
 |
 |
 |
产品介绍
PC-Based CNC Control System
产品特色
* 3轴伺服定位控制
* 5点一般可规划输出入之输出入点
 |
 |
 |
 |
 |
|
||||||
|
||||||
|
||||||
|
||||||
| |
产品介绍
|
|||||
|
PC-Based CNC Control System
|
||||||
| EPCIO-300运动控制模组是利用高整合且多功能的EPCIO-ASIC所开发出来公车铣床专用的运动控制 | ||||||
| 模组。控制模组中包括3轴的定位及同动控制1轴的主轴马达控制，同时具有可接受4轴的马达编码回 | ||||||
| 授信号输入 及1轴手轮输入。2组远端传输的输出入控制介面，每组可接受64点的输入及64点的输出 | ||||||
| ，共有256点的输出入控制点。以及2组的类比转数位输入介面，可接受一般类比电压输入。透过 | ||||||
| EPCIO- 300运动控制模组，控制器中仅需要一片CPU卡及一片EPCIO卡，便可满足车铣床控制器的 | ||||||
| 功能 ，除了体积可大幅缩小外 ，在硬体配线及维护所需的费用，更可大幅降低。 | ||||||
|
产品特色
|
||||||
|
* 3轴伺服定位控制
|
||||||
| * 5轴编码回授信号输入 | ||||||
| * 1轴数位类比输出 | ||||||
| * 2轴类比转数位输入 | ||||||
| * 256点远端串列传输输出入点 | ||||||
|
* 5点一般可规划输出入之输出入点
|
||||||
| 应用范围 | ||||||
| 车/铣床 | ||||||
| PC-Based工业控制器 | ||||||
| 工具机控制 | ||||||
| 产业机械控制 | ||||||
| 半导体设备定位控制等 | ||||||
| Specifications | ||||||
| * Size:185mmX122mm(PC Half-Size) | ||||||
| * System Clock:20MHz | ||||||
| * Bus Interface:ISA Bus , Data Bus:16 bits , I/O Address:20H, Interrupt:IRQ 3,4,5,6,7,10,11 | ||||||
| * Motion | ||||||
| Position Axes:3 | ||||||
| Spindle Axes:1 | ||||||
| DDA Cycle:50 us~6700 ms Programmable | ||||||
| Max. DDA Command:2^10 -15 pulses | ||||||
| Velocity Command Range:+ / -10 volts | ||||||
| pulse Output Format:A / B PhasePulse / DirectionCW/ CCW | ||||||
| Error Counter16 Bits DMA channel:7 | ||||||
| * Encoder ( A / B / Z pulse input) | ||||||
| Interface:Differential or Open Collector | ||||||
| Type:A / B PhasePulse / DirectionCW / CCW | ||||||
| Decoder:x0 , x1 , x2 , x4 ( for A / B Phase Only ) | ||||||
| Latch:15 trigger signals for each axis | ||||||
| Position Counter:32 bits | ||||||
| * I O | ||||||
| Remote IO:128 In / 128 Out | ||||||
| Local IO:5 Dedicate for Power Fail | ||||||
| * D/A Converter:1 channel with 16-bit resolution | ||||||
| * A/D Converter:2 channels with 12-bit resolution | ||||||
| * Compare Register:Encoder Counter | ||||||
| * Interrupt | ||||||
| Drive-pulse output | ||||||
| Error Counter Overflow | ||||||
| Index | ||||||
| Comparator | ||||||
| I/O Input | ||||||
|
||||||
|
|
||||||
|
||||||